How is cantilever rack different from pallet rack?

Pallet rack has a front beam and stores discrete, boxed loads. Cantilever has an open front, so long material loads from the side and slides in without clearing an obstruction - that's the entire reason the system exists.

How far apart should the columns be?

Close enough that the load doesn't sag between arms. A common starting point puts arm spacing at roughly half the load length, with the remainder overhanging each end evenly. We check that math against your heaviest bundle before finalizing spacing.

Straight arms or inclined arms?

Straight arms suit boxed, banded, or sheet goods. Inclined arms, usually fitted with a lip, keep pipe, tube, and round stock from rolling forward off the arm. Many runs mix both across different levels.

Can arms or levels be added later?

Yes. Arms mount at set increments up the column, so levels can be added or repositioned as your product mix shifts, as long as total load stays within the rated capacity of the column and base.

Can cantilever rack support long materials without blocking pallet traffic in Porterville?

Long agricultural manufacturing stock in Porterville needs support that a standard pallet bay cannot provide. Cantilever sets arm positions to bundle lengths and keeps maintenance materials out of the route used by packed pallets. Arm spacing must support the actual load against sag. A long bundle also needs more turning space than a standard pallet. We use your Porterville inventory quantities and operating sequence to decide whether this system solves the problem or whether a mixed layout is a better fit.

Can a Porterville cantilever rack project be phased around citrus packing operations near State Route 190?

Porterville's eastern Tulare County operations connect citrus packing and supply businesses along Routes 65 and 190. A warehouse may handle changing harvest lots, long maintenance materials, and packaging on the same floor, with different access needs for each. Agree the work zones, inventory transfers, access windows, and handover sequence before starting. Phasing is evaluated against your current storage needs and site conditions; uninterrupted operation and a particular completion date cannot be assumed until the scope and approvals are known.

Cantilever Rack warehouse storage system

Porterville, California

Cantilever Rack in Porterville, CA

Long agricultural manufacturing stock in Porterville needs support that a standard pallet bay cannot provide. Cantilever sets arm positions to bundle lengths and keeps maintenance materials out of the route used by packed pallets. Porterville's eastern Tulare County operations connect citrus packing and supply businesses along Routes 65 and 190. A warehouse may handle changing harvest lots, long maintenance materials, and packaging on the same floor, with different access needs for each. Cantilever Rack in Porterville, CA starts with supported long-load storage with an open front and a clear handling path. We review bundle length, load weight, arm capacity, support spacing, and handling equipment before recommending a configuration.

You get a free design consultation, a CAD plan, and an itemized quote for your actual building, not an assumed warehouse footprint. Arm spacing must support the actual load against sag. A long bundle also needs more turning space than a standard pallet. Call (559) 620-5206 to discuss the constraint that is holding up your next receipt or order.

(559) 620-5206

Why Porterville Warehouses Work With Us

Porterville's eastern Tulare County operations connect citrus packing and supply businesses along Routes 65 and 190. A warehouse may handle changing harvest lots, long maintenance materials, and packaging on the same floor, with different access needs for each. Protect the pack-line-to-storage path and plan for both peak fruit volume and off-season supplies. Plano Street facilities should have their own measured turning clearances and staging zones rather than a plan copied from a larger distribution center.

For cantilever rack, that means checking bundle length, load weight, arm capacity, support spacing, and handling equipment against the way your Porterville team actually works. Arm spacing must support the actual load against sag. A long bundle also needs more turning space than a standard pallet. We compare the storage arrangement with the receiving, production, and dispatch space it leaves available, so a higher count does not come at the expense of daily access.

Fresno Pallet Racks connects your project with Warehouse Equipment & Supplies Co.. You can discuss the Porterville plan with one contact, ask for a revised layout, and see the scope in writing before ordering. A free design consultation should explain both the benefit and the tradeoff of cantilever rack; it should not pressure you into a system that mismatches your inventory. Installation timing and any later additions are planned around the actual site and approved configuration.

Free warehouse consultation

CAD layout with position counts

Installation by trusted installation partners

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Operations We Rack Around Here

Local industrial and transport corridors include State Route 65, State Route 190, Plano Street.

Citrus packing

Agricultural manufacturing

Building supplies

How Cantilever Rack Works

Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.

Columns and anchored bases

Upright columns sit on bases anchored to the floor. Base depth is set by load and arm length so the run stays stable even under an off-center pick.

Arms at adjustable heights

Arms bolt or pin into the column at set increments and move as your product mix changes. Straight arms suit boxed goods; inclined arms with a lip hold round or loose stock in place.

Column spacing against sag

Spacing between columns is set so bundles don't sag between arms. A common starting rule places arms about half the load length apart, with the ends overhanging evenly.

Single-sided or double-sided

Single-sided runs go against a wall. Double-sided runs stand in open floor and load from both faces, doubling capacity per base without doubling the footprint.

What a Cantilever Rack Project Includes

Your Porterville cantilever rack project starts with a practical inventory and building review. We collect bundle length, load weight, arm capacity, support spacing, and handling equipment, usable ceiling height, column locations, door positions, and the current traffic pattern. Protect the pack-line-to-storage path and plan for both peak fruit volume and off-season supplies. Plano Street facilities should have their own measured turning clearances and staging zones rather than a plan copied from a larger distribution center. Photos and an existing drawing help start the conversation; dimensions and conditions must be confirmed before an installation plan is finalized.

The CAD layout shows the storage arrangement, operating aisles, level or lane elevations, and the usable position count. We review supported long-load storage with an open front and a clear handling path against an alternative where a comparison helps. The itemized quote identifies the system components, specified capacities, protection, and installation scope. Our team handles the permit side for you.

Delivery and work zones are planned around the access at your State Route 65 or State Route 190 building. Installation follows the approved configuration, with frames or bases anchored as specified, connections checked, and alignment verified. Systems with moving carts, rollers, or wheel beds are checked with representative loads. Arm spacing must support the actual load against sag. A long bundle also needs more turning space than a standard pallet. Your team receives the agreed configuration and capacity information, a layout to use for later changes, and a clear contact for follow-up questions. Do not change elevations or loads without checking whether the ratings and approvals still apply.

Lumber, plywood, and sheet goods

Pipe, tube, conduit, and bar stock

Steel service center inventory

Furniture, doors, and windows

Long or awkward loads currently sitting on the floor

Call (559) 620-5206

Recent Installations

Racking projects completed for warehouses across Fresno and the Central Valley.

View More Projects

Get a Cantilever Rack Quote for Your Porterville Warehouse

Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (559) 620-5206.

Fresno Pallet Racks

5730 N First St

Ste 105 #252

Fresno, CA 93710

(559) 620-5206

Monday - Friday: 8:00 AM - 6:00 PM

Name *

Company *

Email *

Phone *

Where are you located? *

Approximate warehouse size *

Expected timeframe *

Additional Information

I consent to receive SMS and email communications from Fresno Pallet Racks regarding my quote request. Message and data rates may apply. Reply STOP to opt out.

We respect your privacy. Your information will never be shared.